DY-60W-12/48-A

• Design for indoor installation • Protections:Short circuit/Overload/Over temperature • Product cooling way:Natural air cooling • 100% full load burn-in test • Suitable for LED lighting • Mute without interference • 3 years warranty

Product Category:

A Series

DY-60W-A.pdf

Message

Back to list

Product Description

SPECIFECATION
Model		DY-60W-12-A	DY-60W-24-A	DY-60W-48-A
OUTPUT	DC voltage	12V±2%	24V±2%	48V±1%
	Rated current	5A	2.5A	1.2A
	Current range	0-5A	0-2.5A	0-1.2A
	DC output power	60W	60W	60W
	Ripple & Noise ( max) note.2	500mVp-p	500mVp-p	500mVp-p
	Load stability	± 5%	± 5%	± 5%
	Voltage tolerance note. 3	± 1%	± 1%	± 1%
	Setup, Rise time note. 4	/	/	/
	Hold up time( Typ. )	/	/	/
INPUT	Voltage range	180-265VAC	180-265VAC	180-265VAC
	Frequency range	50-60Hz	50-60Hz	50-60Hz
	AC current( Typ. )	0.6A/180VAC 0.5A/220VAC	0.6A/180VAC 0.5A/220VAC	0.6A/180VAC 0.5A/220VAC
	Inrush current	Cold start ≤ 70A	Cold start ≤ 70A	Cold start ≤ 70A
	Incoming line stability	± 1%	± 1%	± 1%
	Power factor( Typ. )	PF≧0.5	PF≧0.5	PF≧0.5
	Efficiency ( Typ. )	≥85%	≥89%	≥89%
	Leakage current	≤ 5mA/260VAC	≤ 5mA/260VAC	≤ 5mA/260VAC
PROTRCTION	Short circuit	The power supply can resume normal operation when the short circuit is removed during power supply.
	Overload	105%-150% rated output power.
	Overload	Protection type: Hiccup mode, recovers automatically after fault condition is removed.
	Over current	After the over current fault is removed, the power supply will automatically resume normal operation.
	Over temperature	Ambient Temperature 70℃ ± 10%
	Over temperature	Protection mode; the product is hiccup state, protect the product from damage, when the fault is ruled out, the power supply is normal.
ENVIRINMEN	Working temp	-10℃ ~ +55℃( Refer to“derating curve”)
	Working humidity	20% ~90%RH non-condensing
	Storage temp.humidity	-40℃ ~ +85℃， 10% ~95%RH
	Temp. coefficient	±0.03%℃(0-5℃)
	Vibration	10-500Hz, 2G 10min. / 1 cycle, 60 min. each axes
SAFETY&EMC	Aging test	Input voltage : 220V 50HZ Rated output current 25℃ , Burn-in 2h
	Withstand voltage	Input and output: 1.5KVAC 5mA 3s input and shell; 1.5KVAC 5mA 3s
	Isolating resistance	Between input and output, input and shell: 500VDC / 100MΩ
	EMC emission	/
	EMC immunity	/
	Safety standards
NOTE	All parameters NOT specially mentioned are measured at 230VAC input,rated load and 25℃ of ambient temperature.
	Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1uf &47uf parallel capacitor.
	Tolerance: includes set up tolerance. Line regulation and load regulation.
	Length of set up time is measured at first cold start .Turning ON/ OFF the power supply may lead to increase of the set up time.